What is the purpose of the well screen on a water well?

WELL SCREENS

This article, written by the American Ground Water Trust was originally published in THE AMERICAN WELL OWNER, 2000, Number 3]

WELL SCREENS - WHAT DO THEY DO?

A well screen is an engineered device used in many water wells to help maintain a good water supply from the aquifer and allow for long-term satisfactory operation of the well.

Water wells are constructed in either unconsolidated materials such as sand and gravel or comparatively hard and (usually) stable bedrock. Well screens are installed in wells where the zone containing the water for the well (the aquifer) is comprised of loose or unstable material. The screen prevents rock fragments from entering the well, helps support the wall of the well and allows water to enter. Silt or sand particles may cause excessive abrasion and early failure of the well pump and/ or plugging of equipment in the home. In addition, sand may accumulate in a well and block off water-bearing zones.

In all wells, it is preferable to have water enter slowly. Turbulent flow can more easily transport particles and agitated water may release minerals and clog up the well. Selection of the right screen and the right length of screen can help improve a well’s efficiency and productive life. A commonly used and effective screen type for water wells uses a continuous slot construction, made by wrapping and welding a continuous length of wire or plastic around vertical rods. Wrapped screens have an elongated triangle shape when viewed in cross-section with the “point” of the triangle oriented inwards so that the outside slot width is small compared to the inside spacing. This design allows particles that do penetrate the screen to continue through without getting stuck.

Screens are also made by precision machine slotting (vertical or horizontal slots) or by making louver openings. Louver type well screens (shutter screens) are typically used only for high yield wells. Screens are made in many different slot or opening sizes and are usually installed by fixing the screen to the end of the casing, which is then lowered down the well to the selected water-producing zone(s) of the aquifer.

Many residential wells in bedrock do not need a well screen. Well screens are not a “one size fits all” item, and if one is needed, local well contractors know how to select a screen and choose the appropriate screen length. For most domestic wells a screen length of 4 to 5 feet is usually adequate. State or local well construction codes (in addition to cost) may influence screen selection.

By all means “screen” your wellhead with a flower display or a “wishing well” but don’t pile soil around the well casing and never use pesticides, manure or fertilizers around a water well.

[© American Ground Water Trust. This article may be reprinted for non-commercial educational purposes provided it is used in its entirety and that reference is made to its source as an article in THE AMERICAN WELL OWNER, 2000, Number 3]

When drill a groundwater monitoring well into an aquifer to take water, some water fills the bottom of the pipe, but not enough to make it work properly. In addition, the water will be filled with sediment and other particles. Well screen will solve these problems.

Water Well Screen is a filter that allows water to enter a pipe from multiple entry points. It can be made of a variety of materials (especially UPVC, HDPE and stainless steel). Water well screen has a large surface area through which water can penetrate. 

It is resistant to corrosion because it will come into contact with water. Besides, It has a high strength to keep the surrounding structure intact. The openings of the well screen can be small enough to block the large number of formations around them. The flow of water through the screen would be consistent.

It is recommended to install water well screen for all environmental drilling operations. It helps extend the life of the well and keeps the flow of water unrestricted. Sand and fine powder sand, these fine particles can be filtered out before water is available. Water well screen help to exclude most of this fine material from well water. 

Different type of Water Well Screen

• Wedge wire well screen

The well screen is made of a variety of SS 304 or 316 and other weldable metals, ranging in slot size from 0.2 mm to 4 mm. The screen and housing are manufactured according to customer requirements with threaded or flange connectors. 

• Bridge type well screen

It has high-strength by resisting twisting, compression and tensile forces.

-Slot sizes: 1.0 mm to 4 mm

-Wall thickness: 6mm or 10mm 

-Diameter from 150mm to 1000mm (can be customized)

-Open area: 6% to 23%

• Simple well screen

They are made of rolled and welded perforated plates. The holes are rectangular, arranged in rows, and the long edges of the grooves are aligned with the tube shafts. Slots range in size from 3 mm to 6 mm with wall thicknesses of 3mm to 10mm. And open areas ranging from 14% to 23%.

Any requirements, contact us now!